Welcome to Custom Style!
Other Ways to Follow:
Sewing that's Retro, Geek, and Chic
Since social media moves fast and things often get completely missed or quickly buried in the constant flow, I’ve decided to assemble some of the miscellaneous sewing tips I’ve shared on Instagram and publish them together in a single blog post. That way it’s a little easier for you to link, find, and reference later.
So whether you missed them before or just forgot about them (some of these are over a year old!), I hope you savor these quick tidbits! Enjoy! =)
You might recall that I like to trace sewing patterns (especially the vintage ones) to preserve the original. But I also like to use my printer to copy the pieces that are small enough to fit on a page or two.
Spray-n-Bond is my new favorite thing! It was the only way I could appliqué stretch crushed velvet on top of another layer of stretch crushed velvet without it shifting all over the place. It even made using a walking foot unnecessary!
Remove beads from the seam allowance by smashing them with a hammer. This will keep all the beading threads intact so the beads you leave on the outside don’t become loose and fall off as easily. (Protect your eyes! Wear safety glasses when pounding beads!)
Ease with pins. (You don’t need to use gathering stitches to help with easing!) I do this all the time and with all ungathered sleeve caps. Pin both ends, then pin the midpoint, and keep pinning the “middles” until you have the ease distributed evenly.
When you need to gather tightly or are using a thick fabric and you’re afraid of breaking a thread when you pull the gather, zig-zag over nylon or upholstery thread (or even dental floss!). You can then pull the stronger thread without fear of it snapping off mid-gather. Just be sure to secure the other end to the fabric or knot it to another row of gathering stitches.
If you have a presser foot with a hole for stitching over cord or trim as pictured above, it’s even easier.
Sew a stitchline to follow when seam allowances are different widths or uneven. This is especially helpful when attaching bias tape without pins. (Larger stitchline at far right was for basting two layers of fabric together.)
Create a topstitching guide with painters tape for things like a fly-front zipper. (It took me until the third pair of pants to remember this trick!)
This is particularly helpful when sewing on net or loosely woven fabric when a knot won’t catch and stay.
Do you have any favorite quick sewing tips to add? Share and/or link to them in the comments!
So over the course of a week, I made myself three pairs of skinny pants.
Way back in… APRIL!
(I am so far behind in blogging!)
I needed some more work pants for my part-time job at the fabric store and I decided I’d make some because 1) I hate pants shopping and 2) pants are easy to sew once you have a well-fitting pattern.
I’ve never really bothered to draft myself a custom pants sloper because I’ve always been able to find jeans that fit me if I search long enough in stores.
My biggest problem with ready-to-wear (RTW) trousers is the fit of the waistband. Most waistbands seem to be cut like funnels – hips and crotch curve might be perfect but the back waistband majorly gaps on me. (I have, however, found a couple of brands and specific style numbers in those brands that actually fit well, even in the waistband.)
So I pulled out Butterick pattern 5682, traced it in my size according to the size chart, and then compared it to two pairs (different brands) of store-bought skinny jeans that fit me really well.
I don’t remember all the exact changes I made, but the main differences between the RTW and paper pattern were the leg width, the height of the waistband (especially in the front), the back pocket size, and the crotch curve.
I needed to trim down the crotch curve – more noticeably at center back than front. If you can get the crotch curve right, that’s half the battle for fitting a pair of trousers!
The pattern only included one pocket size, which meant that it was proportionally wrong for most of the sizes in the envelope. Proper pocket proportion and placement is important! (Afterall, you don’t want “gateway mom jeans” because of “dinosauric pockets”.)
So I reduced the pocket size to match my RTW skinnies and referred to the factory placement when making my own.
With my pattern corrected well enough on paper, I pulled out some black metallic stretch denim I had. There was enough yardage to re-cut if I needed any major alterations, but I was fairly certain the fit would be close enough to the RTW jeans I like.
I decided to use some fun cotton fabric to line the front pockets. No one will ever see it but I know it’s there! =)
After a quick assembly and matching the details on my RTW pairs, I had a pretty good first pair.
I ended up adding half an inch to the hem length on the pattern but the black pair is just long enough. I also curved the waistband a little more to prevent my next pairs from having the slight gap at center back that the black pair has.
Knowing that I never tuck my shirts in, especially when wearing skinny pants, I called the metallic black pair “good enough”…
…and moved on to a second pair – this time in a floral print stretch jacquard:
I carefully cut the fabric so the stripey-ness of the floral print would match across the legs and then broke up the print on my tush with intentionally unmatched pockets – something that will hardly ever be seen because of that untucked shirt thing, but still.
I still had one 3-inch metal fly zipper left, so I decided to make a third pair of skinny pants out of some textured stretch jacquard. (I love love love this fabric! You will be seeing it again because I bought it in 4 different colors.)
I didn’t do anything fun for the pockets on my floral print pants because the pants themselves where fun enough. I decided the teal pants needed interesting pockets though.
I had three good options in my cotton print stash – Tube map, tiny turtles, and bigger happy turtles. So I turned to Instagram/Twitter for a vote.
My first try-on and I think I finally got the waistband curve exactly right! Third time’s a charm and all that. This pair of pants is definitely the most comfortable.
I did more topstitching detail on my teal pants than I did on the other two pairs. I also cut them out one layer of fabric at a time in order to keep the textured design evenly horizontal across each piece – typical making-things-overly-complicated-just-because-I-can mode of operation.
Here’s a back view of the finished teal pants. (After all the picture sorting and editing, I’m reeeally tired of looking at my butt!)
Pair number four will be perfect – if I ever decide I need to make myself another! I went ahead and corrected the pattern just in case.
I chose to mimic the look of the buttonholes on my RTW jeans. I made the loop by tracing around the shank of the jeans tack button and bringing it to a point. I used some embroidery/cross-stitch thread and just zig-zag stitched over it following the line I drew.
I’ve been wearing all three pairs of skinny pants a lot for my retail job at the fabric store. The metallic black pair is a little too warm in the summer (all that metal retains body-heat and reflects it back) but it’s a nice basic without being boring because of the sparkle. The floral pair is just plain fun & trendy. And the teal pair is super comfortable and probably my favorite.
So anyway, I made some pants. Trousers. Whatever.
And it took me so long to blog them, that it seems everyone else in the online sewing community has now made and blogged their own in the meantime! Ahead, but behind all at the same time.
Over on Instagram, lots of us who sew have tons of fun sharing what we’re currently working on and cheering each other on. Sometimes, I get comments asking for more details and photo examples.
Recently, I was asked how I mark and sew darts.
Since I had a mockup with a lot of darts in line for my next project, I posted the step-by-step as I built the mockup. It seemed popular, so I thought some of you who may have missed it on IG would like to see it as a blog post tutorial. =)
First, cut-notch each leg at edge of fabric. (Obviously, you can’t do this with darts that aren’t at the edge of a seam.)
Put a pin through each dart point before unpinning the pattern piece. Unpin pattern, open to fabric wrong side & mark dot with pencil, chalk or whatever works on the fabric you are using.
For straight darts, line a ruler up with marked dot & notch at edge and use Clover Chaco Liner or a pencil to draw legs.
For curved darts, you can put pins thru at intervals down each leg and dot mark same as points.
Use a french curve to connect the dots. (You can line up french curve on paper pattern & then place on fabric to make sure curve matches.)
Start pinning at dart point (about a mm from dot). Weave pins through 4x, and make sure to go through the lines on both sides. Second, pin at notched edge to help fold dart evenly. Then continue weaving pins through from point to notched edge (right to left).
I like assembly-line dart sewing. Do you think this vintage pattern from 1959 has enough darts??
Hand crank needle into end of dart right through marked line and remove first pin.
Stitch directly on marked line. Guide fabric with left hand and hold next pin head with right hand, allowing the machine to pull each pin out as you go.
Reduce stitch length when close to end point of dart.
I like to stitch off the edge of fabric at point and usually backstitch inside of previous stitchline. Sometimes I just stitch off and hand knot thread ends – it depends on project & fabric.
Pull out a tailor’s ham and start pressing all those stitched darts. Yay done! Time to start actual construction…
And in case you’re curious, this is the pattern (pencil skirt version) I was using for my mockup:
And Happy Geek Pride Day!
Today I’m spending the afternoon working at the little local fabric store and wearing my newly made Star Trek comic print skirt.
I didn’t use a pattern for my skirt. It’s just a basic petticoat-style skirt with an elastic waistband, which I made with rectangles of fabric. (More details in a minute.)
I still have plans to remake a better fitting knit Dandelion top a la TOS style, but I haven’t gotten to that point in my sewing queue.
So I’m just wearing an old store-bought polo I’ve had in my closet for years with my new skirt. The polo’s a bit too long for the skirt, but it’ll do for now.
I’ve had this fabric for months knowing I wanted a geeky skirt out of it. I was even able to print-match across the seams without losing too many inches!
Here’s a simplified how-to diagram to explain making the elastic-waistband skirt (detailed instructions following):
Mine finished about 19½-inches long (knee-length worn a couple inches below waist) using the following measurements & steps:
Here are a couple of sewing tricks I like to use:
This skirt works really well with a petticoat underneath so I pulled out my ‘50s style petticoat (it’s an XL kid’s size so it’s shorter than the period appropriate length).
My husband hates the petticoat look but I love it!
It required spinning.
We will see how many fabric store customers notice my geekiness at work today or even know what today is. By the way, I always keep a towel in my car – but my dog gets more use out of it than I do.
Speaking of the dog, you might be wondering “where’s Wensley?” because he usually likes to photo bomb. Believe me, he tried but there was a door in his way this time:
And I leave you with this silly picture, because I still like the skirt best with the petticoat underneath:
One to beam out. So long, and thanks for all the fish!
I’m still alive* and sewing, I promise!
Most recently (aka last week), I made myself a Sewaholic Cambie Dress.
I know that anyone who has read sewing blogs for the past few years has probably seen one or fifty versions of this dress. Honestly, I’ve seen so many – and while I’ve always liked them – I just sort of filed the information away thinking that maybe someday I’d try the pattern for myself.
Well, that “someday” finally came and I ordered a couple of patterns from Sewaholic Patterns to see how they fit my body. Here’s my Cambie:
I made it in a brightly colored large-weave cotton with 2% spandex piqué fabric. I love textured fabrics, especially when they are a solid color!
The color of this fabric is incredibly hard to photograph! It really messes with the white balance on cameras. I’ve discovered that digital cameras want to read anything with a mix of green and blue as bright turquoise with all the green removed. (Must be that whole Orion slave girl makeup issue on film.) The fabric is definitely green but it has a drop of blue in it – a color somewhere in the zomp and Persian green range in this article about the color spring green on Wikipedia.
Anyway, I think I’ve come pretty close to color-correcting these photos to match real life.
I made a mockup of only the bodice to check the fit. (I knew both skirt options would fit just fine without adjustments.)
The only changes I made to the pattern were so minimal they’re almost not worth mentioning. I scooped out the underarm a little (it was awfully high and straight), smoothed the neckline curves slightly, and shortened the front shoulder straps by a full inch (apparently a commonly needed alteration for this pattern), as you can see in the mockup photo above.
I also decided to make a neckline facing instead of fully lining the dress. I chose to do this because my fabric was rather thick & didn’t need one, and I didn’t want to lose the comfort of its slight stretch.
Speaking of hard to photograph colors, this fabric is also hard to color-match with thread! I never did find a perfect match. Good thing there’s no topstitching needed with this design! I ended up using emerald green (too green!) thread on my serger and a teal (too blue!) thread to stitch everything together.
I made View A with the A-line skirt. I really like the full gathered skirt version too and will probably make one in View B at some point.
All the above photos show how I wore my new dress to church on Sunday. I went with neutral wedges and a simple necklace to make it all about the dress the first time. But I know I’m going to have lots of fun pairing it with other accessories later!
I particularly like it with the yellow shoes and narrow belt:
In the end, I was surprised how dressy this fabric actually is. (I probably shouldn’t be, considering piqué has long been associated with white tie.) I’ve always thought of piqué as somewhat casual because it’s cotton and usually used for summer dresses. But this larger weave has a shimmer to it as the light hits the texture.
You may have noticed that Wensley likes to photo bomb my blog pictures. So to conclude, here’s a goofy shot of me imitating him jumping at the back door during the shoot:
* After a bunch of costuming jobs, I came back to find that WordPress had messed with some of the settings for inserting photographs, making their newest “upgrade” more of a downgrade. Incredibly frustrating and un-motivating when it comes to blogging! So while I waited for them to get their act straightened out, I spent my time sewing a lot of things for myself. And now I have a backlog of things to blog.
It has been far too long since I’ve had a chance to sit down and blog! That doesn’t mean I haven’t been sewing – just more work sewing than fun sewing.
At the beginning of January, I decided my sewing room needed a major cleaning/reorganizing. I spent a couple of weeks rearranging the furniture in my sewing room and adding a few new pieces. I think it will really be more efficient in the long run. (More on that to come in a later post.)
I got about 90% finished with the reorg and then I started getting back-to-back jobs and the last 10% has been taking the longest to finish.
But before I got work-busy, I did manage to build myself a new ironing table! Yes, table! No more wimpy ironing board for me! You might recall that I’ve been using the square end of my ironing board and ignoring the pointed end for years.
I’ve always loved the large tables set up in costume shops where I’ve worked (there are usually multiple irons sharing one large surface). It was high time I had my own personal table at home!
And because I know all of you who sew will want one for yourself, I took lots of photos so you can make one too. =)
I’m not sure how long IKEA’s carried this, but I just noticed it recently. It was exactly the size/height I’ve been looking for to use as an ironing table base, and it is solid wood. Plus, it even had the bonus of drawers and shelves!
So for $149.00, I had the perfect table base and I didn’t have to engineer anything from scratch. (I still find it amusing that the least expensive large piece of furniture in my sewing room is the cutting table!)
The dimensions of the NORDEN sideboard are 47½” long x 16½” wide x 35⅜” tall. The height was perfect but the top surface was a little small. I needed something that wasn’t too big and would fit along the wall where I already had my ironing board without blocking the closet door.
First, I constructed the sideboard table exactly as the IKEA comic book instructed because I had come up with my own simple plan to make the surface bigger without having to alter the original design.
I wanted a surface area that was significantly larger than my ironing board, which measures 13½” wide x 53” long (to the narrow pointed end). I decided 60” long would be a decent size to fit my space while still being long enough to iron fabric yardage in one pass from selvage to selvage.
I also determined that 19” wide would not take up too much space in my room – I had to be careful not to make my sewing room feel crowded with the other furniture rearranging.
Then, my husband and I went shopping to buy some supplies at the home improvement store:
We already had these but you will also need:
We cut each square dowel into 3 pieces measuring 3”, 14.5”, and 18.5”. The small 3” pieces were a good size to keep the dowels from blocking the drawers on the front of the sideboard. Exact size is not important as long as you are able to frame each corner of the existing tabletop with the dowels.
We turned the IKEA unit upside down, placed it on the plywood top, and marked it so the base would be centered on the plywood lengthwise. (Note: make sure you remove the adjustable shelf before turning table upside down!) We offset the sideboard table a little closer to the front edge so that the dowel would be flush with the edge of the plywood (thus, prettier and easier to cover).
Then we put some extra plywood scrap on the floor underneath everything. This was so we could drill all the way through the plywood top without worrying about drilling into the carpet beneath.
Starting with the two small front dowels, we butted them up to the edge of the sideboard and drilled one hole all the way through the dowel and the first layer of plywood that would be the new top.
Then we unstacked everything and put bolts through from the top (the part that was facing the floor while drilling) and attached them with washers and nuts on the dowels on the bottom.
After that, we did the same with one dowel on one side – drilling one hole on each end because this piece of dowel was longer.
We continued drilling, unstacking, and attaching one dowel at a time so we could make sure everything fit perfectly and would be tight around the sideboard.
Finally, we had the dowel frame all attached. It didn’t matter that the bolt heads weren’t perfectly flush with the top surface because I knew the padding I would be putting over everything would smooth any height difference out. As long as the dowels were secure on the plywood, it was perfect.
I initially had plans to secure the plywood top to the IKEA sideboard after covering it with appropriate ironing fabric, but it ended up fitting so snuggly we didn’t need to. For once, one of my crazy IKEA hacks actually turned out to be less complicated than originally planned! Win!
You may have noticed I was able to move my fabric tubes from under my cutting table to under my new ironing table. This was perfect because with my new furniture arrangement, the tubes were a little more in the way under the cutting table.
Next came the hard part: waiting for specialty fabric to come in the mail so I could cover the plywood top.
The best ironing tables in costume shops are covered in a drapery interlining fabric called English bump cloth. I read somewhere (apparently I failed to save the link) that it was first used as a curtain interlining for British royalty in order to better insulate palaces from the cold and damp.
Bump cloth is a thick, somewhat flannel-like fabric that adds body and structure to fancy drapes.
I found some at Fabric.com in my first search and placed an order. Even though the website said there was around 40 yards in stock at the time, I received an email a couple days later saying they were sold out. Grrr. (I have had such rotten luck with Fabric.com completely filling my last few orders!) If you feel like taking a chance with them, here’s the link for their Hanes Drapery Interlining Bump Cloth listed as item #UK-528.
Once I learned I wouldn’t be receiving my first order of bump cloth, I started looking elsewhere. I eventually found some at BuyFabrics.com and it was less expensive than Fabric.com’s! I quickly ordered 2 yards (I was planning to use two layers to cover my plywood top) and they shipped within 24 hours! Here’s their link for English Classic Bump Natural Interlining.
While I waited for my bump cloth, I went to my local JoAnn Fabrics and purchased 2 yards of aluminum coated ironing board fabric in their utility fabric section. (You can also buy it on their website.) I knew I wanted another silver ironing surface like I had on my ironing board before because it looks better for longer. Most costume shops cover their ironing tables in muslin, but leakage from irons stains muslin.
As of yesterday, Fabrique! (the little fabric store where I work part-time) also started carrying silver ironing board fabric! You can order it from the website as well. From what I can tell, this fabric might have a slightly heavier muslin backing for the aluminum than what JoAnn sells. Too bad I wasn’t able to buy it from work when I needed some!
Finally, my bump cloth arrived and I could finish my ironing table!
The following steps can be used to cover any wooden table surface to create an ironing table if you already have a piece of furniture and don’t want to buy a NORDEN sideboard.
I discovered, even after pulling the bump cloth tight, there was still too much slack when I rubbed the top surface. So I pushed the extra up toward the front of the tabletop while my husband held and spring clamped the excess in place.
Once the plywood top was completely covered, we just pushed it in place on the sideboard. It fits nice and snug. If I ever need to recover it, I can just take the top off and change out the fabric that needs to be replaced. Super easy. =)
I love my new ironing table!
Bonus: I no longer need to iron yardage in steps before I roll it – I can roll as I iron! And all my ironing tools fit in one drawer while my press cloths & ironing products (aside from interfacing) all fit in the other drawer. I chose to hook my sleeve board over the right edge of the tabletop because I use it often and it makes the tool drawer a bit crowded. I don’t need to leave everything on the open shelf above where it gets dusty – now I only keep spray bottles and sizing etc. on the shelf above.
I just need to clean up the used gravity-feed industrial iron I bought used years ago, and I’ll have totally finished my ironing upgrade!
I hope you find the above tutorial helpful and are inspired to build your own ironing table! Send me a photo or link if you do – I’d love to see!
So, you may have noticed my previous post was a bit long. But did you stay with me till the end? Did you see there was a giveaway? You did? Well, it’s time to announce the WINNER!
And thank you for all the nice comments! It means a lot to me when I get some even from those who aren’t wanting to enter a giveaway!
As with my past giveaways, names were placed in the hat:
My husband drew the winning name, and the lucky winner of the Spearmint coat pattern is:
Congratulations, Fwaire! Please email me your mailing address and I’ll put your pattern in the mail. =)
So I’ll be drafting a new collar and adding some other details. I think I’m going to make this version unlined, with bias finished seams on the inside. It will be an olive-y cotton corduroy:
Of course I wish I had copies of the pattern to send to everyone else who entered, but you can buy a copy from Lolita Patterns in downloadable pdf or already printed on pattern paper. A sewalong will be coming soon on the Lolita Patterns blog.